HOT ALONE WON‘T DO THE TRICK!

HOT ALONE WON‘T DO THE TRICK!
Posted by moko14am on 2021/08/17
HOT ALONE WON‘T DO THE TRICK!

    HEATING ELEMENTS


    About 5000 to 7000 furnaces for sintering zirconia are produced every year at the moment. The numbers are rising. There are two different heating element

types that are installed in the dental furnaces on the market to achieve the extremely high temperatures, usually in excess of 1400°C (2552°F). By far the

largest share of the furnaces on the market is built with molybdenum disilicide (MoSi2) heating elements. In some few cases, silicon carbide (SiC) heating

elements will be used. These two element types differ in their properties in addition to the entirely different basic materials.


    SiC heating elements are usually used up to a temperature of 1530°C (2786°F) as

recommended by the furnace manufacturer. A firing cycle will take several hours. MoSi? heating

element
s can be used up to a temperature of 1750°C (3182°F), depending on the quality and furnace type. The maximum application temperature of these

heating elements therefore is clearly above that of SiC heating elements. Additionally, the surface load, which means the power (W) that can be emitted

per square centimeter (cm2) is more than twice that of SiC, at above 25 W/cm2. This permits much faster heating-up rates, to much higher application

temperatures. Heating to 1550°C (2822°F) in less than 15 minutes is possible.


    MolyCom?-Hyper 1800 (MoSi2) heating elements that have been used on the international dental market since 2005 have turned out to be much longer-lived

than SiC elements in continuous tests and according to the experience of various furnace manufacturers. SiC elements usually need to be replaced after just a

few hundred cycles due to the strong change of resistance, which corresponds to a service life of approx. 1-2 years at common use. MolyCom?-Hyper 1800

elements in contrast have been operated for more than 2500 cycles without any failure or need for exchange. Exchange of the defective element is usually

sufficient in MoSi2 heating elements. In contrast to this, all parts of the SiC elements must be exchanged in one due to the strongly impaired

resistance.

    If we additionally compare the chemical analysis of the heating elements, the standard heating elements show a much higher degree of contamination, in

particular by iron oxide. No contamination could be measured at use of the MolyCom?-Hyper 1800 elements up to a temperature of 1630°C (2966°F). No

contamination was measured for MolyCom?-Hyper 1800 Super Clean elements up to 1680°C (3056°F).


    Additionally, a contaminated zirconia sample on the surface was analyzed with a secondary ion mass spectrometry (SIMS). As the analysis shows,

increased contents of iron oxide could be documented in the sample up to a depth of 0.15 μm. While the degree of contamination is very low, it has a

considerable visual effect. The vapor pressures of many different oxides at the surface temperatures of the MoSi2 heating elements in the furnace were

additionally calculated with Fact Sage. 


    Among the ceramic materials, silicon nitride ceramics possess good overall performance (e.g.,

high hardness, high strength, low density, low thermal conductivity, low chemical activity, and high wear resistance), which promotes these applied as

rolling bearing, machine tools, sliding bearing in water pumps.

    Aluminum titanate has outstanding properties that make it ideally suited for applications

involving molten aluminum, including complete resistance to wetting by aluminum alloys, total gas impermeability, and a very low thermal expansion

coefficient. This material offers a longer service life and higher reliability when compared to cast iron, calcium silicate or fused silica

components. All riser/stalk tubes are 100% leak-down tested, and parts are available with gasketing and ceramic foam filters to provide complete

assemblies.



    Alumina ceramic is an industrial ceramic that has high hardness, is long wearing, and can only

be formed by diamond grinding. It is manufactured from bauxite and can be shaped using injection molding, die pressing, isostatic pressing, slip casting, and

extrusion.


    Reaction bonded silicon carbide has excellent wear, impact, and chemical

resistance. The strength of RBSC is almost 50% greater than that of most nitride bonded silicon carbides. It can be formed into a variety of shapes,

including cone and sleeve shapes, as well as more complex engineered pieces designed for equipment involved in the processing of raw materials.


    Ceramic fiber paper is a must-have for those who work in the manufacturing industry. It’s a type

of the high-temperature insulated paper that’s integral to many manufacturing functions. For one thing, ceramic fiber paper has a huge variety of

applications — whether it’s protecting gaskets (like rope gaskets) from high temperatures or providing insulation — and there’s a range of grades and

thermal conductivity, depending on what’s needed. If you’re looking to purchase ceramic fiber paper, we’re your best bet — we’ll discuss some of

the benefits and applications that you might not have expected out of this material and what you should expect when ordering and handling it. 


    One of the major benefits of using ceramic fiber paper is that it has a low thermal conductivity and doesn’t store much heat. It’s also thermal shock

resistant and is resistant to most chemicals, which means it has a low corrosion rate. It’s great if you’re looking to die-cut or use automatic stamping

and has high dielectric strength as well. 


    Another benefit to this type of paper is that it’s lightweight and uniform in its structure, which makes it a great type of insulation. It’s also

flexible and fire-resistant! 


QR code
Report this ad Leave a review

Related ads